Ever wonder what you're neighbours are doing to improve their homes? Discover what other Mississauga homeowners have planned for their Electrical projects by reading the details of their request for quotes below.
In total, TrustedPros has received 251 Electrical projects posted by homeowners in Mississauga seeking the services of local Electricians. Total estimated value of these projects is $1,878,000.00 with a per project average of $7,482.00.
|City||#Projects||Total Value||Avg Budget|
I recently purchased a Level 2 Jukebox 40 Pro charger and require an install in the garage.
Require about about 25 feet of 8 gauge wire from the finished basement fuse panel into the garage. Also there does not appear to be any spare panels, a sub panel is required. Will require an inspection permit to receive government rebate.
Basement currently has 3 incandescent flood lights that I would like replaced with eight 3" 50 watt GU0 bulbs. Housings are included in the kit I purchased. The ceiling panels are removable 2'x2' squares and I will replace these with 2'x4' wood fibre ceiling panels after pot lights are wired- replacing the ceiling panels is not required by the electrical contractor - I will do this myself.
In our master bedroom we currently do not have a light fixture in our ceiling. We would like a fixture, capable of supporting a ceiling fan, installed in our room. Additionally, we would pay for the contractor to assemble, wire, and install the purchased fan (purchased by me).
Additionally - there is currently 1 wall switch that is wired to a standard 120V outlet (wired for a floor lamp) that we would like to control the light to the fan. The switch has been installed on the wall immediately as you enter the bedroom. If the light switch is on - the light to the fan is on, and when the switch is off the light is off - we would still like there to be power to the fan so that the fan can circulate air, even when the room is dark.
Our master-bedroom does have attic access through a crawl space. The room has 10ft cielings and is approximately 15 feet x 10feet. Our home is an end-unit town home, and was built in 1997.
Have 4 ceiling fans that need to be installed in upstairs bedrooms. There is currently a light fixture in each room; however, the light fixture is not mounted to the beams. The ceiling fans needs to be mounted and installed.
Please provide a rough estimate for the full cost of installation.
I need a certified electrician to install a hanging light fixture in my dining room. There are currently 4 potlights in the corners of the room. A hole would have to be cut into the ceiling in the centre of the room and wiring installed, pendant hung, and a dimmer switch installed. I also require that patching to any holes be made. I have attached a picture of the light fixture. Please respond with a quote and pics of any similar projects you have completed. Many thanks in advance :) PS - I live in Mississauga (Winston Churchill and Eglinton).
I am looking for well reputed and experienced contractor to do my following jobs in Mississauga area.
1. Complete site services.
2. Concrete foot path/curbs and flower beds in parking lot.
3. Complete electrical job with led light poles.
4. Landscaping of entire project.
For immediate response contact Malik.
Need to get a lot of electrical work done in my kitchen as follows:
Supply and install additional wiring
install pot lights, pendant lights, under valence lighting,
Wiring for built in oven.
Relocate Intercom station and telephone jack to new location
Age of House : About 16-17 years
Previous Renos: None
My home was built probably in the 1970 and has aluminum wiring on the main floor and the basement its a semi detached back split in mississauga
So I am wondering what the cost would be to get the pigtailing done properly or to put in the proper AL/CU outlets and switches. Only looking for estimates at this time.
I'm renovating a house in bloor/cawthra area. Renovation is in progress now, so this job is for right now. I'd say about 2/3 of the 1700 square foot house is exposed (drywall down) already. Can you let me know if you'd like to quote stringing copper, replacing aluminum (which was used at the time of construction). its a rental, I will be price sensitive.
House is 1400 sq feet fully wired and operating. We have electrical issues:
Every bathroom outlet is not working (never worked after we moved in the house in november 2011)
recently changed outlet covers in guest bedroom ( 2nd floor) now light in kitchen in a few outlets don't work anymore.
Would like to have this fixed soon and cheap.
I have 5 rooms that have no lights. These rooms have light switches but they only power a wall socket in each room. What I need is the light switch to power a normal light fixture in each of the 5 rooms. You will have attic access.
4 rooms are on the upstairs floor - the 5th room is the main living room on the main floor. There's lights in the room already but we want to add 6 potlights to the living room.
I'll need the lights to be completed to the socket - no bulbs or fixture needed.
Please price material cost and labor.
Looking for estimates only. (project length and cost)
The service box is currently 100amp which i believe will need to be upp'ed. The major appliance outlets in the kitchen will need to be adjusted and in some cases moved slightly. The following areas will need to have potlights installed. (looking for LED style potlights)
-Living Room: 247 sq/ft
-Kitchen: 310 sq/ft
-Family Room: 209sq/ft
-Master Bedroom: 132 sq/ft
-Bedroom 1: 143 sq/ft
-Bedroom 2: 143 sq/ft
-Bedroom 3: 143 sq/ft
I would also like smoke and carbon monoxide alarms to be installed via hardwire.
We have recently reconfigured a part of our office which included moving 4 cubucles a few feet over from their original position. These cubicles had power and data cords running inbetween them through a "jifi" tower. We now need that tower to be moved to connect to the new location of the cubicles. Also, my desk is no longer attached to those cubicles therefore power will also need to be connected to my desk.
Hopefully this is good enough of a description.
I am looking to do a Reno in May of 2013. We would like to do the demo ourselves but want to do the following:
-replace aluminum electrical with copper and re route electrical outlets
-removal of old gas fireplace/baseboard heaters/current poorly installed AC unit
-mid range kitchen renovation (one wall knocked down)/pass through to dining room created-we have a computer design drawn up and products in mind
-floors kitchen/dining/living/foyer (harwood/laminate)
-mid range upstairs bathroom gut and replace with current layout (products such as vanity/toilet and lighting will already be purchased
If you could get back to me that would be great with quote/time of job
I am looking for master electrician who can do this job with permit.
Basement area is around 750 sq ft.
- Full basement finishing as per electrical code regulations.
- Rough in, wire and install all new Decora plugs and switches.
- Install approximately (30) 4 inch recessed non - IC rated pot lights.
(pot lights will be supplied by customer)
- The new pot lights will be installed throughout the basement.
- Run wiring for data and cable to new location of the TV area.
- Cat6 wiring will be used for data
- Full wiring, lighting and exhaust fan install for a newly constructed 3
- Complete wiring for lighting with a switched feed in storage room
- Complete wiring for lighting with a switched feed in
- Complete wiring for lighting with a switched feed in the existing cold
- Complete rough in for a new stove hook up and exhaust fan for a
- Complete rough in for a new washer and dryer hook up with exhaust
- 2-3 Decora dimmers and 3 way switch.
Require electrical work in basement of 1960's built home in Mississauga, ON.
Require all outlets / switches be upgraded (original outlets currently in home).
Require installation of approx. 12-16 insulated potlights onto one main switch.
Basement is currently wired for several lights that are not working and/or have been removed. Job may require removal of old wiring in ceiling (and possible junction boxes). Ceiling will be removed prior to electric work being supplied so it will be open & available.
I am looking for a certified electrician for an unfinished basement.
Nature of the work includes:
-Setting up pot lights
-Setting up switches and plugs
-Replacing some existing light fixtures around the house*
-Replacing some existing plugs and switches around the house*
I am available to meet in the evenings.
I'm looking for someone with experience to do this job for me because I am not too great with wiring.
This job requires wiring an ethernet cable from the main floor (inside an exterior wall) to the finished basement directly below it.
I will attach a picture here which indicates the location, walls, and truss direction which may or may not be important to you. Feel free to contact me if you need other information to provide a quote.
I actually need a few things done and am hoping that I can get these done at the same time thru the same person/people.
1. Need an exterior door installed (Garage to house). There was an opening during construction but due to miscommunication, they closed it up and put up the drywall.
2. Garage door opener install + motion sensor lights outside and inside garage.
3. Dishwasher install. Rough-in exists.
I need to get these done asap. Depending on the rough estimates I get, I would want to setup an inspection soon to finalize this work.
I am located in Mississauga; Near Derry and Mchlaughlin.
Please feel free to contact me for more details.
Looking forward to hearing from you.
I have started kitchen renovation and I am looking for an electrician to rewire my kitchen with new wires.
Wherever possible I would like to avoid opening the walls.
Basement right below the kitchen is finished, but it is possible to see/run cables from the laundry room to the panel.
I would like it to be done some time next week (Sept 10 - 15)
Post your project and let top-rated pros compete to get your business. Compare bids, read real customer reviews and hire the best contractor the first time.Click here to get started