Ever wonder what you're neighbours are doing to improve their homes? Discover what other Oakville homeowners have planned for their Tiling projects by reading the details of their request for quotes below.
In total, TrustedPros has received 39 Tiling projects posted by homeowners in Oakville seeking the services of local Tiling Contractors. Total estimated value of these projects is $179,000.00 with a per project average of $4,589.00.
|City||#Projects||Total Value||Avg Budget|
Please provide estimate for the following scope of work
Scope of project:
1)Installation of coiffered ceiling, painted with crown mouldings in family room (20 ' x 15') and upstairs hallway (26' x 10')
2)Installation of pot lights (approx 12 to 15) in upstairs hallway (inside coiffered ceilings)
3)Replace and upgrade existing kitchen backsplash tiles
4)Install under lighting under kitchen cabinets
Online estimates must be provided prior to any site visit. Thanks to all for your time and estimates. Only responses within parameters will be contacted.
New granite counter tops are being installed on Friday Sept. 12 and I would like to have someone install the back splash immediately after.
I would like to have a kitchen back splash installed by a professional who does this work regularly. The walls are clear and free of any previous tile work. We will supply the tile and grout unless you have samples at the same rate as Home Depot. You will supply steel edging and glue. Aprox. $10 per sq/ft.
We have decided to not tile behind the stove and fridge.
There is 40 sq/ft to be installed.
Looking to install a kitchen back splash. Tiles we have selected are 2 X 6 Glass subway tiles.
Approx sq footage: 37-40
Long counter (sink side): 139 inches long x 20 inches high (counter to under cabinets)
Stove counter: 74 inches long x 20 inches high
Section over the sink: 12 inches high x 30 inches wide
Section over the stove: 12 inches high x 34 inches wide
Small section beside fridge: 18 inches wide x 12 inches high
Basement apartment has kitchen with broken tiles. Tiles removed and new tiles are 1 cm too big on both sides- I searched all manufacturers of tiles and the closest I could find are a little too big, but match thickness and colour.
Need new ones cut and installed asap.
Located at 4th Line and Upper Middle
brand new house and subdivision, I already have the tile delivered at my home
kitchen = 300 sq ft (needs removal & dispose of 13x13 old tile and install 12x24 marble)
foyer = 75 sq ft (currently subfloor and install 12x24 marble)
laundry = 75 sq ft (currently subfloor and install 12x24 porcelain)
contact me as soon as possible, eager to get started
Tiling - remove old tile, install new 12 x 24 inch porcelain tile and re-install existing baseboard. Customer will supply own tiles, grout and ditra.
Kitchen: 19.32 x 11.68
Laundry: 6ft 2€ x 10
Foyer: 6ft 4€ x 6ft 4€
Foyer Closet: 5ft 5" x 2ft 4"
Powder room: 4ft 10€ x 4ft 10€
Hardwood flooring - remove old solid hardwood, install new solid 3 1/4 oak hardwood, re-install existing baseboard. Customer will supply new oak hardwood only.
Living: 12.01 x 10.83
Dining: 10.99 x 9.51
Family: 15.49 x 10.99
Hallway 1: 12 ft 7 x 5 ft 10
Hallway 2: 5 ft 5 x 5 ft 7
-Take out existing railings and install them back
-Sand, stain and varnish staircase (total: 15 steps)
-Sand, stain and varnish stringers. (total: two sides)
-Install new iron spindles (total: 92 spindles)
-Sand, stain, varnish and install existing railing (total: 40 feet)
-Install, Sand, stain, varnish and new 3/4 inch straight nosing (total: 24 feet)
-Install, Sand, stain, varnish and new 3/4 inch curved nosing (total: 6 feet)
-Install, Sand, stain, varnish and new oak shoe molding (total: 22 feet)
-Stain and varnish new posts (three posts)
Customer will supply iron spindles and newel posts.
Customer can provide a 15 ft bin rented from Waste Management for old tiles and hardwood.
Location is in Oakville, work to begin Nov 1st.
We have a tile job of roughly 800 sq foot. We'd like to use a larger format porcelain tile (more than 12") potentially on a 45 degree angle. The areas covered would be the kitchen, laundry room, bath and foyer. We'd like advice/help picking tile that will not be slippery if it gets wet, and that has a good blend of colours (not white).
I would like to receive an estimate for regrouting, caulking and sealing of a
corner shower stall. The shower stall has 5 walls, 4 walls have white
ceramic tiles (6x6 in large) and one side has a glass door. The four tile walls
have the following width measurements: 40 in, 39 in, 17 in and 19in. The
height of the shower stall is 82 in. On the floor there are small white
ceramic tiles 2x2in.
The grout on the floor is sanded and the grout on the walls is non-sanded.
8 year old house, just moved in. Yet to use the ensuite shower because inspector said moisture collecting behind walls. grout is noticeably missing for 1 or 2 inch stretches. Approximately 100 square feet ot tile. Corner unit, ensuite shower with glass door. undecided on material as of yet but more than likely it will be ceramic. Will purchase all materials needed, just tell me what to buy.
Looking for an estimate to remove and re-tile corner shower stall in our master bathroom. Dimensions are 36" x 36".
I will provide tiles and fittings (faucets & shower heads).
Also looking to replace existing curtain with a glass door.
I'm looking to get this done asap.
Please mail me back with questions i.f any
Thanks in advance
Front hall tiles.
I am a contractor looking to subcontract the following work.
Install 45sf of front hall/closet tiles.
No natural stone.
I will provide, mesh, mud, tiles, and grout.
I will have the area ready to go, old tiles removed, and trim removed.
I need this job done next week.
Please message me with your references/availability/quote
1. We can supply materials or the contractor can supply - quote both
2. Polished Marble (Crema Marfil select) in the foyer and hallway (approx 350 sf) with borders/patterns,
3. Full body porcelain (polished) with borders/patterns in Kitchen - approx 350sf
4. Subfloor already installed but not levelled. Tiles to be instaleld on concrete base (approx 1 inch thick)
We are expanding.
I can provide trades with consistent work.
Please email me with what your trade is, references, and how you price.
I look forward to hearing from you.
If you are a general contractor please don't respond. I am looking to deal directly with trades.
Post your project and let top-rated pros compete to get your business. Compare bids, read real customer reviews and hire the best contractor the first time.Click here to get started