Ever wonder what you're neighbours are doing to improve their homes? Discover what other Scarborough homeowners have planned for their Electrical projects by reading the details of their request for quotes below.
In total, TrustedPros has received 69 Electrical projects posted by homeowners in Scarborough seeking the services of local Electricians. Total estimated value of these projects is $284,000.00 with a per project average of $4,115.00.
|City||#Projects||Total Value||Avg Budget|
Install Duct work in 2 story condo townhouse, malvern area, with gas furnace and central air conditioner.
apx, 2000 sqft. Above grade condo townhouse, end unit over 25 years old.
My clients would like to convert the existing Electric/Baseboard heating system to forced air, gas, with cac, also needs Duct work installed.
They are looking to start the project at the end of the month.
30 year old detached bungolow in east scarborough needs to have electircal updates:
1) upgrade from 100 amp to 300 amps
2) 3 seperate panels
the upstairs has 3 bedrooms, kitchen and 1 washroom, living room and dinning room.
Basement has been divided into 2 seperate self contained apartments. so i would like each of these two apartments to have they own electrical box.
The home has copper electrical. Please email me with your quote for this job.
I need an estimate on electrical work for the installation of an 18 inch dishwasher. It only needs a regular voltage plug to run. There is an outlet above the backsplash (about a meter or 2 away) where you can retrieve power. There are no cabinets in the way as they will be torn down.
Please provide an estimate, thank you.
-We believe our panel has sufficient space for the extra load and will not need to be upgraded. We need to run the wiring from the panel room, out to the side of the house, along the house about 50 feet to where the pool will be.
- Service to the swim spa must be dedicated 240V, 50A 3 wire plus ground (#6
AWG copper with minimum #8 AWG copper ground).
- The swim spa must be hooked up to a “dedicated” 240
volt, 50 amp breaker and GFCI.
- The pool being hooked up is a 15 foot H2X by Master Spa
I'm thinking of getting some electrical work done in the near-future for my house. It's a small townhouse, around 1200-1400 sqft with 2 floors and a basement built around 40-50 years ago. One of the main things I want to do is upgrade the current fuse box to a bigger circuit breaker box.
There are also a few changes I want to make to some of the wiring. The previous owners had switched the living room and kitchen, but didn't setup the kitchen circuit with a high enough current to properly support multiple kitchen appliances. There's a light in one of our hallways that doesn't seem to turn on. And there's another light at the staircase with a light switch on both the first and second floors, but it's not a 3-way switch.
I want to see approximately how much to budget for something like this. Depending on costs, the priority is the kitchen wiring followed by the circuit breaker.
Lights started to flicker and dim. Heating elements on stove not working although stove lights are on. Thermostat is on but heat pump does not turn on. Some circuits have very low power in them, while other circuits are OK. No issues with power being supplied to our condo building according to Toronto Hydro.
Please provide a price for the following.
We can provide drawings for the project but we are looking at a fast start on Thursday January 2, 2014 and need a good crew. We will send reflected ceiling plan for the electrical new vs old and what is to be replaced and re-wired.
The kitchen area walls and ceilings are being gutted and opened up to the back of the house ie. Living room and skylight hallway and extend the cathedral ceiling from the front breakfast area to the skylight hallway. This entire area will need requiring.
The existing baseboard heaters will be replaced with new as noted on drawings. A heat/loss drawing and calculations will need to be prepared (engineer) to determine what size of baseboard heaters and how to determine the efficiency of the existing furnace and slab on grade ducting at parts of the kitchen, skylight hallway, living room and 2 bedrooms, and entry hall vs the baseboards in breakfast, dining room, master bath and master bedroom.
The existing 200 amp panel is located in the kitchen at the south wall, where the existing mast is located. But it's also in the future pantry cabinetry. One idea is to create a sub-panel in the water meter closet near the front entrance and leave some of the existing circuits in the current location.
The electrical price shall include rough in and finish and obtaining electrical permit as well as coordinating inspections and as follows.
All material listed below shall be supplied and installed by electrical contractor unless specified by Owner.
Outlets and switches shall be white "Decora"
Included in this list are any existing outlets that need upgrading and switches changed to new or dimmers, as well as any These will be noted as existing to be retrofitted ie. Duplex outlets changed to child safety and current ESA std or light switches changed to Decora with dimmers. Most lights will be on dimmers except for closet lights.
SUMMARY OF NEW MATERIAL LISTED BELOW;
1 sub-panel( 24 breaker?) or re-use existing 200 amp and smaller sub panel at water meter closet
duplex outlets 8 new and retrofit 35
1 exterior GFI outlets retrofit
5 interior GFI outlets
8 light boxes
slide dimmers( low voltage)
15 halogen low voltage pot lights( halo or equivalent) and retrofit 9 others with existing metals boxes
exterior soffit incandescent pot lights (not at this time)
2 vapour proof shower lights
3, 220 CFM bath exhaust fan (determine how large for the small bathroom vs the larger ensuite bathroom in the master, laundry closet)
2 combination Smoke/CO detectors
Power wiring for ,... to be determined
Electric radiant floor heating and thermostats shall be installed in kitchen, breakfast and entry as per dwgs, and in both bathrooms
All switches, dimmers and receptacles shall be white €œDecora"
finalize at site visit.
The bungalow house has 100 Amps fuse panel. I want this to be changed to 200Amps circuit breaker panel. In addition I want to move the meter box out side the house from basement. The supply now is from overhead. I would like to know the cost and what service panel box it will be replaced with. If possible give me the cost for material and labour seperately.
Full electrical for adding basement second unit:
Install of approx. 5 ceiling fixtures
Install of approx. 20 pot lights
Install of approx. 22 receptacles (including stove plug and dryer plug)
1 Fan line for bathroom / fan
possible line for range hood
2 interconnected CM/SA detectors
possible upgrade panel
1 SA Bedroom, 1 SA kitchen
house is about 50 yrs old.
need breaker panel (currently fuses)
need capping of various junction boxes in attic and few in crawl space (there are pot lights installed throughout the house)
need to move exterior outlet from immediate vicinity of gas meter
issue with faucet/sink in laundy area; faucet was taped when moved into the house, don't know problem.
issue with kitchen sink... appears that there is no 'trap' and therefore odor is constantly present.
Add power outlet to cupboard safely for power to the over the range microwave oven. The power line is already there that was installed for the exhaust fan. I want safe and quality three prong outlet put in cupboard.
The house is 6-7 years old.
Reinstall new pot light fixture for basement. Current potlights fixtures are MR16 50 W power, recessed with no insulation around the fixture.
8 lights in basement to change. in 200-400 square foot area.
I would prefer to somehow use less heat dissapating GU10 or MR16 LED bulbs. I am not having any problems with current lighting fixtures . I do not like the heat generated by halogen lights and I am worried about if the current fixtures will allow use of MR16 led bulbs or if they can be changed to GU10 connector type.
I am just currently trying to see what the options are for making changes to the lighting in the basement .
I have some minor electrical jobs to be done at my residence.
1) An electrical outlet installed on the exterior of the house (front yard facing).
2) A light to be installed in my backyard on the deck, I have one light available the same wire can be pulled for the second light, so that one electrical outlet that is available on the inside can control both the lights.
3) A sensor light that is installed at the side of my house, keeps going on/off (maybe the light isn'f fixed right, or the wiring is loose) -- needs to be looked at.
4) A light to be installed in the basement store room.
I am looking for a electrician to service 2 sensor lights on the left exteriro walls of my home. I have a walkout basement and the
lights are placed at the top and bottom of the stairs which does not work. The 1st set of lights does not come on and the 2nd
set of lights keep going on and off when switched on. Both set of lights are controlled by 1 switch in the panel box.
I need to get an estimate how much it would cost to service it for the lights to work properly,.
I will like to get an electrician to install 2 light bulbs on the exterior walls of my home. One bulb will be placed on the top of the staircase
and the second bulb will be placed somewhere in the middle of the exterior wall. The wiring for both bulbs will connect to 1 switch which will be placed on the inside wall on the front of my home. I will like to get an estimate how much it will cost.
Main 100A breaker recently started tripping after the dryer has been on for a few minutes. Main breaker is warm to touch after tripping. The dryer is connected to its own fuse box that is unaffected--only the main breaker trips so I believe the problem may be with the main breaker/connections, not the dryer itself.
Panel is at least 15 year old Commander model using white breakers with black switches. Main breaker is 100A.
I am looking for a Certified Electrician to Install a transfer switch and inlet box into my home so I can run a backup generator when needed.
The home is brick with cinder block foundation.
The generator I have now is 7000 Watts and has 1 120/240V 30 Amp twist lock outlet.
Don't yet have a Transfer Switch Kit so please provide quote with/without parts.
Thank you for your time.
I would like to sand and repolish the floor of my house. I am also interested to know about the cost of laminate the floor. The floor of the house is roughly 740 sqft. Anybody who does such job and interested please send the quote per sqare feet for both (sanding and repolishing / laminate).
I also want to change the baseboard.
I also have to do some electrical work described below
Garage line Double Tapping correction
Fix reverse polarity on some outlets
Correct some ungrounded 3-prong outlets
Please email me if you are interested.
I need a licensed contractor to come in and provide estimate and then if approved do the work necessary to to get the work done. I am applying for the gas line with Embridge, I need the HVAC contractor to fill out the necessary paper work and then provide hook up services to the appliances in the house.
Recently moved into older house (1955). Some issues with general electrical condition. Outlets for dryer and stove (? 220V) are loose / hanging, may be unsafe. Track lighting in living room is amateurish, may need repairing or replacement / installation of additional track lighting elsewhere on ceiling.
Need to level ground and run electrical for hot tub installation. Only need 2 inches of limestone in an 8 X 8 or 9 X 9 foot area. Electrical panel is near the front of the house in the basement. Basement is half finished. Hot tub will be at the back of the house just in front of our deck. 50 to 70 ft of wiring. Can supply my own limestone. How much for all of that and just electrical. I might do the leveling myself.
Post your project and let top-rated pros compete to get your business. Compare bids, read real customer reviews and hire the best contractor the first time.Click here to get started