We have a hi-rise condo property that has had its laminate flooring damaged due to a water break. We will need to have a contractor remove the all the laminate flooring and discard. It will be a 2 phase project as dehumidifier and fans will have to dry the concrete slab first. There will also be some very minor drywall and baseboard re installation/ repair. As some of it was cut away at base to dry out one section of wall. Area of work is 300SF
Working times will be 9-5 Mon to Friday as per Condo rules. Our company will coordinate with Condo management to reserve service elevator.
Estimated Schedule:
Day 1: Demo and removal of all damaged laminate
Day 2-4: Dehumidifer and fans to dry slab- seperate vendor
Day 5-6: Reinstall Laminate flooring/drywall patching and replace damaged baseboards
Our company will provide the laminate flooring, underlayment, quarter-round and section of baseboard.
I was interested in creating a hidden shoe storage upholstered bench that could fit my entryway space needs. It would be the height of a dining room chair seating, 3 feet in length and 1 foot wide. It would open like an oven door and have shelves inside to house shoes. I have a picture of what I want with a few modifications to make it look more modern.
I need a carpenter to do:
1) beef up a support beam in Kitchen
2) frame in a door/wall - around the basement stairs
3) install firewall in shared attic.
Location is: Oakwood & St. Claire
Home is 70-80 years old - semi-detached bungalow approximately 800 sq. ft.
I have already gutted it so there is easy access. I need the work completed as soon as possible so the electrician can begin.
If a list is provided I can supply materials if it brings the cost down or you can provide them.
Looking for experienced contractor /carpenter to instal an interior door from the foyer to our boardroom. Job includes
- pick up door and trim (GTA)
- remove existing trim/drywall around opening
- instal new trim
- instal door and hardware
Photos of opening attached.
Ground floor job
Parking on site.
We just purchased a townhouse condo built in the mid 70's, recently renovated that has four floors. We have a busy 1 year old girl and need stair railings built for safety. We would need three different railings put in.
We are looking for white, wooden railings. The first railing would be 10 feet in length, the second 7 feet long the other around 6 feet long. The stairs are carpeted, I have photos of two of the sets but not really a good one of the third set of stairs which would be the smallest railing length. Each staircase approx 30-35 degrees.
I am looking for a carpenter to do the following work in this week or early next week:
I would like to get the installation of baseboards and quarter rounds (approx.:46 linear foot), doors (three main doors + 1 small door for closet), windows framing (three windows).
Need the following installed for a new construction (no demo/removal work):
1. Six interior doors with frames and trims
2. Two sets of closet slide doors with frames and trims
3. Five window trims/casings
4. One existing door needs to be re-positioned (pulled out by a few inches so that it is flush with new drywall).
5. Closet needs to be built around electrical panel.
Im finishing up my home reno, and Im looking for an interior finish carpenter or contractor to install my trim (baseboards and casings)
I also need someone to install my balusters, posts and railing on my staircase.
All material has been purchased already.
There's about a weeks worth of work to be done.
Im in west Toronto, close to dupont/lansdowne.
Please call or email.
Hi,
There are a few smaller jobs that need to be done to finish our house.
We are looking for someone to finish the interior trim: The kitchen, living room, and some small parts of upstairs need baseboards and quarter round finished.
There is one window, and two doors that need trim.
Tile the back splash of the kitchen and behind the stove.
We have the glass for an exterior front door that needs to be installed.
Build a set of simple stairs in the bedroom leading to the the outside deck.
New front stairs to the house.
We would also like to build boxes to encase the radiators, there are 3.
Thanks.
Hi,
I have a kitchen island in a condo in which one side is storage, but I was thinking of trying to make the storage side into a breakfast bar instead. The dimensions of the kitchen island are:
height - 92cm
width - 141cm
depth - 64cm
I have attached some pictures of the current kitchen island, and some examples of what type of end product I am looking for.
Thanks!
Good day,
I am looking for a carpenter who does rough framing. I am looking for someone who will do more than framing, such as some demo, installation of vapor barrier/insulation, prep work, just an all around knowledgeable person. I also need this person to be extremely knowledgeable on building code and what is and is not allowed. Needs to know point loads, structural knowledge etc. I also need him to know how to do great decks. I am getting very busy and my right hand man who did all of this has left. Must have own tools and own vehicle.
We tore out a bank of cupboards and had the electrical panel upgraded that was inside the cupboard. Now we need to complete the area with a custom media/electronics cupboard to match the existing PDF cupboards in the basement (electrical work for the electronics is done) and a door installed for the electrical closet. Would like a really good carpenter involved. The entire project needs finishing touches.
Thanks much.
We are looking for additional mill work fabricators and installers for commercial projects. The fabrication is critical for the relationship and potential candidates must have their own fabrication facility. Installers are advised to identify themselves as just "installers" .
Thank you
J. Radu
Looking to have a bar designed for a salon, that seats 6 people, at bar height level. Purpose of bar is to perform manicures, in a "bar" setting. bar stools will be used on both sides of the bar for seating. 1 by customer, 1 by employee servicing the customer opposite from them. Would like this done as soon as possible.
One of the GTA's best Design/Build renovators is seeking a very qualified Lead Hand Carpenter. This position requires over 10 years experience in renovations, no exceptions. We need a full carpenter that has a solid track record of additions and major renovations (our average project is ($150K)
This individual will be working directly with the owner, who manages all major projects. Qualified carpenters need no further explanation.
References will be checked.
We provide an excellent working environment with lots of creativity, problem solving and stiff challenges.
We are a close knit team who work well together and occasionally socialize together.
This will be a long term position with a solid, 34 year old company.
Please send your full details, CV if you have it, images of your work and references.
Andrew
Just finished my laminate floor and I need baseboard installed. I will supply the baseboard. The square foot is roughly 350-400. It will be baseboard plus the little trim that goes at the bottom of the baseboard. Example of possible baseboard. I'm located in Milton.
Please try to quote by pictures.
- You will need to provide I.D and proof of your own insurance.
- I'd like to get this in before Christmas.
General Contractor looking for experienced carpenter to start immediately. Looking for experienced carpenters to handle various mid size projects in the GTA.
Requirements:
Must have 5-15 years experience as a carpenter
Must be able to read blueprints
Must be familiar with best construction practices
Knowledge of the Ontario Building Code and Health & Safety
Own all or most required tools?
Own a valid driving license and transportation
Must be responsible and reliable
Please reply to this posting by email only with your following information:
Credentials and qualifications
Experience
Availability
Payment preference (per hour or per contract)
Best Regards.
Hi,
I've got six pieces of douglas fur (2" by 8", around 5-6 feet long). I need about an inch shaved off of them so they'd be 1x8s and the ends cut on an angle. As well, i would like one of the pieces to have a lip (so basically looking to cut a 1x6 section into the board). The intended use is for a mantle, and the piece with the lip on it would be the front board.
I would expect this to be a simple job with the right equipment, and I can bring the boards to you.
Thanks in advance for your help.
I am looking for a knowledgeable and creative home bar designer and installer for my basement. Will need at least two cabinets at the back with two-tier glass shelves to display liquor bottles. There will also be a bar fridge, sink, microwave, wine rack and wine chiller. Looking for someone to start ASAP. Please email or call to schedule an estimate.
Thank you
Hi we are about to start an attic renovation and need a carpenter who as experience building open stairs. We will provide all materials and on site access for measurements etc. Must have references and pics of previous jobs, and off site workshop would be an asset as there is very little room to fabricate on site.
Post your project and let top-rated pros compete to get your business. Compare bids, read real customer reviews and hire the best contractor the first time.
Click here to get started