Hello,
We need someone to install vinyl and aluminum siding on a house extension. We will need fascia, eaves trough, soffit and down pipe. Location Danforth and greenwood area.
Please contact me if you are available to perform this service soon and to arrange a time for a visit to give an estimate.
Thanks
Replace the windows, siding and eavestroughs in the dormer. Dormer is part the uninsulated attic space. Replace the leaning porch column with a pressure treated 6x6 the full height (remove existing brick and timber column) and a new concrete sono tub foundation my be required. I also want to replace the eavestrough at the porch and some of the soffit and cover around the beam at the porch roof.
To remove supply and install:
- soffit, fascia eaves-trough, down pipes at east side of house.
Determine if 1x6 wood fascia needs to be repaired or replaced.
Remove all aluminum siding (2nd floor of house) and install vinyl siding cap in aluminum around window frames and put drip edges at top of windows to divert water.
Ground floor exterior wall needs some durable weather proof cover, eg. aluminum siding, or possibly other fireproof veneer. Wall is currently covered with insobrick. Area to be covered is approx. 9' x 7.5'. Tight access - 17" from neighbouring house. Downtown Toronto. Must have T85 licence & insurance. References. Job to be done in next 30 days.
I have a small 2 storey semi-detached, approximately 23'x16' built early last century. Bad renovation done probably in the late 80's. Exterior is stucco.
I am looking for a contractor to give me an estimate on removing the stucco and installing a pre-finished wood siding (Cape Cod or similar) rain-screen wall, including rigid insulation and moisture barrier. There are some tie-ins to windows and roof decks that would be affected by the work. Probably also includes some soffits to be re-finished.
Hi,
I own a home on Toronto Island and am looking to get my exterior walls and insulation redone. It's an older home and the exterior walls only have 2/4 insulation. I'm hoping it will be possible to add additional insulation on and redo the siding. Toronto Island has a ferry that can transport vehicles.
Please let me know if this is work that would interest you.
Hi, I live in a semi detached around lansdowne and Brandon which is over 100 years old. We are looking to replace our current aluminium siding, and redo our soffits, eavesdrop and fascia, as well as the aluminium around the windows. We are looking to also looking to install insulated siding either vinyl or aluminium.
I already have siding on front and side of house but would like to replace it with a darker colour and possible reuse present siding (which is in excellent condition) on the back of the house. the budget section didn't leave a lot of leeway so I though I would add my budget is approximately $1500 or a bit more.
We have an external garage in an old Toronto home. The external wood siding of our garage on one side is starting to rot. If you look at the pictures, there are holes on the wooden boards near the ground.
We are looking for a quite to replace the wooden panels that have rotted, which looks like the bottom 2 or 3 boards.
- replace existing siding + soffit and replace with new vinyl siding + soffit
- front of house: only small top half section needs replacing
- back of house: first and second floor levels need replacing;
- side of house doesnt require any changes
- also need to modify current downspout configuration to optimize drainage (current configuration does not drain very well)
Status Construction Ltd. is launching our new Homes by Status development in the GTA and we are looking to contract new sub trades for services.
If you or your company is looking for a new opportunity for home building and services of the following:
-Drywall, Taping, Plastering
-Electrical
-Plumbing
-Floor installers
-Tile Setters
-Painting Services
-Fine Carpentry, Millwork
-Disposal Services
-Cleaning Services, Ductwork services
-Stucco
-Aluminum, Eavestroughing, Siding
-Windows and Door providers
We want to hear from you! Let us know about your company, your capabilities and interest in our homes. We expect proof of insurance, WSIB coverage and references of work is preferred.
You will be added to our trades service list.
We have an animal that's living in the walls at the rear of our house. We believe it's entering between the foundation and the siding. We're looking for a way to keep the animal out. This will most likely involve removing some of the deck boards that block access to the foundation. We believe that the animal has also torn up all the insulation as this part of the house is quite cold. We assume the animal has ripped up the insulation. We'd like that addressed as well.
Our house is missing two 8' long sections of fascia. We saved one as template for new replacement. We would like to have these previously white pieces and the lower sections that connect to them be coloured grey instead. Also require two 7' sections of eaves trough and a 20' piece to be covered with leaf guards. The existing 4 window shutters to be matched with the same grey.
We require an estimate.
Hello,
My office is right around the corner from you on Galaxy.
I need to have my backyard shed re-sided and wondered what materials you offer? The shed is approx 10x20' and I need all 4 walls sided - there are approx 375 sq feet.
I was considering a cape cod or something similar, perhaps cedar shakes. The shed will be used as an outdoor bar/tool shed, so I am trying to add some atmosphere to it.
Please get back to me with some options and price points. I need to have this re sided by Aug 24th.
Thanks,
Eric
We have bought a shed that is already tar papered on the roof and already has been wrapped on the outside. The shed is approx. 8 1/2' x 11 1/2' and approx. 13 ft high (from floor to peak of roof). We want it vinyl sided including soffits an fascia and shingles put on the roof. We probably need eaves but that will depend on the cost of the job.
This is a small project, and we have been given some outrageous prices. We are looking for a fair price for a small job. We have costed out the siding anywhere from 75 cents a sq ft to 1.30 a sq ft. This is not the taj mahal, it is a shed. There is a door a skylight and a medium size window.
The shield sits on the driveway of the seller. We need this work completed by Wednesday April 29 or sooner because we must remove it from the sellers property.
SCOPE OF WORK
- Supply and install 1x3 strapping over rigid insulation
- Supply and install blue horizontal Hardie Board plank siding
- Supply and install white 1x4 corner, window and door trim
- Total wall area = 890 sq. ft.
West Elevation
- 1x4 trim around 1 - 3’x6’ window
- 1x4 trim around 1 - 4’x6’ window
- 1x4 trim around 2 - 2’x3’ windows
- 1x4 trim around 1 - 8’x7’ door
- Supply and install white 1x8 fascia (18 ln. Ft.)
- Supply and install white soffit (30 sq. Ft.)
We are open the option of aluminium siding if it saves on cost. (we just need to achieve a fire rated product as we are at lot lines).
Please request drawings and we will send it as upload function is not working.
I have a top up project in OAKVILLE.
The top up is 47'X23'6", 10 feet for the height. 1410 sqft not including window and double door cut outs.
I am looking for a sub to provide supply and install pricing for this job.
The client has asked for two dormers to be added to the front elevation, which will be priced as extra to the 1410 sqft above.
Please contact me via e-mail to arrange for a site meet to see the project.
SCOPE OF WORK - (Laneway House)
Exterior Finish Scope of Work
- The contractor will supply and install the exterior cladding as follows.
- North and South elevation exterior cladding is 7/8" corrugated metal siding designated as C12 by Agway Metals or similar, color to match the C20 Hardie Panel. There will be approximately 567 sq. ft.
Note: The cladding will be omitted where a neighbouring structure exists along side the laneway suite.
- East and West elevation have PVC Lap Siding, 6" plank format on the first floor designated as C01 by Chamclad or similar, color to be determined. The second floor will be a Hardie Panel designated C20 (changed from C13) and installed on 1"x3" PT strapping @ 16" o/c, color to be determined. There will be approximately 224 sq. ft. of C01 and 260 sq. ft. of C20.
-Prefinished aluminum soffit, fascia and trough to match in color to the Hardie Panel. The prefinished aluminum flashing is also required to cover any exposed rigid insulation around the foundation.
- Downspouts will go down to grade level with discharge for a splash pad.
- The contractor will remove all leftover material and dispose of and remove debris.
I manage a six-storey residential building in the area of Etobicoke, ON. I need to get some estimates to have siding installed on the west end of the building in the same fashion as the east end was done a few years ago. The siding was installed as a result of water seepage through old brick. The building is approx. 50 years old.
Best bet is to visit the site. Arrangements can be made to have someone walk you around if required.
Attention Siding Trades:
Our company is expanding and as a result we are looking for QUALIFIED trades to quote the various projects we have. We do both Residential and Commercial work and need trades in every aspect of work.
What we need from you:
To be a specialist in your trade, if you’re a drywall company great; please don’t tell us your speciality is also siding….
Your papers need to be on file with our office:
• Business License
• GST #
• TRADE License (if Applicable)
• WSIB
• Falls Certificate (if Applicable)
• Insurance Certificate
• Union Papers (Commercial If Applicable)
•
Also, as well please send us any references you may have. We require at least 5 that we can contact.
Thank you
Post your project and let top-rated pros compete to get your business. Compare bids, read real customer reviews and hire the best contractor the first time.
Click here to get started